PCB Manufacturer & PCB Assembly

Grid setting skills In the PCB layout design

Posted on April 08, 2018 by G

PCB design needs to set different points in different stages. In the layout stage, large grid points can be used for device layout.

5149 1 0 Shares

Engineers conclude: PCB design goes from shallow to deep

Posted on April 04, 2018 by G

When I saw the PCB of a computer motherboard, I thought I was able to draw a great thing myself. Later when touched protel99se and entered the drawing board team, followed by Altium, Cadence, and so on. As the experience of the drawing board accumulated, more and more issues were noticed. A good PCB board is not only connected to the line.

4557 1 0 Shares

The definition of the circuit diagram

Posted on April 03, 2018 by G

The circuit diagram, which is a schematic diagram of the connection of the electronic components drawn by symbols of the circuit components, describes in detail the connection and direction of each component, the description of each pin, and some detection data.

5190 1 0 Shares

Several methods of analyzing common circuits

Posted on April 03, 2018 by G

To master several methods of analyzing common circuits, familiarize yourself with the circuit types and analysis steps that are appropriate for each method.

4407 1 0 Shares

Circuit schematic entry knowledge

Posted on April 03, 2018 by G

The significance, classification and composition of electronic circuit diagram

6078 8 0 Shares

PCB design should consider the hole size of the pad

Posted on March 30, 2018 by G

The pad design is designed to achieve the smallest diameter, which is at least 0.5 mm greater than the maximum diameter of the weld terminal orifice flange. The test pads must be provided for all nodes in accordance with ANSI/IPC 2221. Nodes are two or Electrical connection points between multiple components. A test pad requires a signal name (nodal signal name), the xy coordinate axis associated with the reference point of the printed circuit board, and the test pad's coordinate position (describe the test pad On which side of the printed circuit board). The information needed to provide fixtures for SMT will also need to be printed on the assembly technique of the circuit board assembly to "fix the device in the circuit test" or commonly referred to as "fixed nail bed." With the help of devices" to promote testability in the circuit. In order to achieve this purpose, you need to:

4827 1 0 Shares

PCB shape and size design method

Posted on March 29, 2018 by G

PCB shape and size are determined by the placement machine's PCB transmission method and mounting area.

4232 2 0 Shares

High-frequency circuit layout techniques in PCB Layout

Posted on March 28, 2018 by G

10 techniques

5107 1 0 Shares

Cadence allegro and Altium and other software comparison

Posted on March 27, 2018 by G

Schematic design software, ORCAD is OK. Netlist is basically the industry standard.

5560 6 0 Shares

Cadence allegro16.5 use skills summary

Posted on March 26, 2018 by G

23 use skills

7018 8 0 Shares

The most critical five points in the PCB design

Posted on March 22, 2018 by G

A perfect PCB:

4644 1 0 Shares

Shielding method in high-speed PCB design

Posted on March 21, 2018 by G

The transmission rate of high-speed PCB design and cabling systems is steadily accelerating, and it also brings about some kind of anti-jamming vulnerability. This is because the higher the frequency of transmitting information, the higher the sensitivity of signals, and the lower and higher the power of their signals. The wiring system at this time is more susceptible to interference. Interference is ubiquitous. Cables and equipment can interfere with other components or be severely disturbed by other sources of interference, such as: computer screens, mobile phones, motors, radio transmission equipment, data transmission, and power cables. In addition, potential eavesdroppers, cybercriminals, and hackers continue to increase because of their enormous damage and loss to UTP cable information interception.

4577 1 0 Shares

Teach you to easily get the PCB component selection in the package

Posted on March 06, 2018 by G

All of the examples in this article were developed using the multisim design environment, but the same concepts apply even with different eda tools.

4893 1 0 Shares

PCB review principles in the process of layout

Posted on March 05, 2018 by G

Four principles as below:

4106 1 0 Shares

Detailed 0 ohm resistor role

Posted on March 02, 2018 by G

People think that the earth can absorb all the charges, always maintain a stable, is the ultimate reference point. Although some boards are not connected to the earth, but the power plant is connected to the earth, the power of the board will eventually return to the power plant into the ground.

5279 1 0 Shares

PCB schematics passed to the layout design tips

Posted on August 25, 2021 by G

PCB Best Design Methodology: Six things to consider when passing a PCB schematic to a layout design. All examples mentioned in this article were developed using the Multisim design environment, but the same concepts apply when using different EDA tools.

5092 1 0 Shares

Tag: PCB schematics