Contact Us
Blog >> Blog Details Page

Several issues that should be taken seriously by mobile phone PCB design

Posted:04:46 PM July 04, 2018 writer: G

Even if the wiring in the entire PCB board is completed well, the interference caused by the inconsistency of the power supply and the ground line may degrade the performance of the product, and sometimes even affect the success rate of the product. Therefore, the wiring of electricity and ground wire should be taken seriously, and the noise interference generated by electricity and ground wire should be minimized to ensure the quality of the product. For every engineering engineer engaged in the design of electronic products, the reason for the noise between the ground and the power line is understood. Only the reduced noise suppression is described:

(1) It is well known to add a decoupling capacitor between the power supply and the ground.

(2) Try to widen the power supply, ground line width, preferably the ground line is wider than the power line, their relationship is: ground line > power line > signal line, usually the signal line width is: 0.2 ~ 0.3mm, the most The fine width can reach 0.05~0.07mm, and the power cord is 1.2~2.5mm. For the PCB of the digital circuit, a wide ground wire can be used to form a loop, that is, a ground net is used for use (the ground of the analog circuit cannot be used in this way)

(3) Use a large-area copper layer for grounding, and connect the unused areas to the ground on the printed board for grounding. Or make a multi-layer board, power supply, ground line each occupy a layer.

2. Co-processing of digital circuits and analog circuits

Many PCBs are no longer single-function circuits (digital or analog circuits), but rather a mixture of digital and analog circuits. Therefore, it is necessary to consider the mutual interference between them when wiring, especially the noise interference on the ground. The frequency of the digital circuit is high, and the sensitivity of the analog circuit is strong. For the signal line, the high-frequency signal line is as far as possible away from the sensitive analog circuit device. For the ground line, the whole human PCB has only one node to the outside, so The number of processing and the common ground must be handled inside the PCB, and the digital ground and the analog ground inside the board are actually separated from each other, but only at the interface where the PCB is connected to the outside (such as a plug). The digital ground is slightly shorted to the analog ground. Please note that there is only one connection point. There is also no common ground on the PCB, which is determined by the system design.

3. The signal wire is placed on the electrical (ground) layer.

In the wiring of multi-layer printed boards, since there are not many lines left in the signal line layer, the addition of layers will cause waste and increase the workload for production, and the cost will increase accordingly. To resolve this contradiction, consider wiring on the electrical (ground) layer. The power layer should be considered first, followed by the ground layer. Because it is best to preserve the integrity of the formation.

4. Treatment of connecting legs in large-area conductors

In a large area of grounding (electricity), the legs of common components are connected to them, and the treatment of the connecting legs needs to be comprehensively considered. In terms of electrical performance, the pads of the component legs are perfectly connected with the copper surface, but There are some hidden dangers in the soldering assembly of the components. For example, 1 welding requires a high-power heater. 2 is easy to cause a virtual solder joint. Therefore, taking into account the electrical performance and process needs, making a cross-shaped pad, called heat shield, commonly known as thermal pad (Thermal), so that the possibility of creating a solder joint due to the cross-distribution heat during soldering Sex is greatly reduced. The treatment of the grounding (ground) leg of the multilayer board is the same.

5. The role of the network system in the wiring

In many CAD systems, cabling is determined by the network system. The mesh is too dense, although the path is increased, but the stepping is too small, the data volume of the field is too large, which inevitably has higher requirements on the storage space of the device, and the computing speed of the object computer electronic product is also Great impact. Some of the paths are invalid, such as occupied by the pads of the component legs or occupied by the mounting holes and the holes. The grid is too sparse, and too few paths have a great impact on the routing rate. Therefore, there must be a sparse and reasonable grid system to support the wiring. The distance between the legs of the standard components is 0.1 inches (2.54mm), so the basis of the grid system is generally set to 0.1 inches (2.54 mm) or less than 0.1 inches of multiples, such as: 0.05 inches, 0.025 inches, 0.02 Inches and so on.


  • PCB
    Prototype
  • PCB
    Assembly
  • SMD
    Stencil

Dimensions: (mm)

×

Quantity: (pcs)

5
5
10
15
20
25
30
40
50
75
100
120
150
200
250
300
350
400
450
500
600
700
800
900
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
7500
8000
9000
10000

Other Quantities:(quantity*length*width is greater than 10㎡)

OK

Layers:

Thickness:

Quote now