NextPCB

New Life with Your NEXTPCB!

Turnkey PCB manufacturing & assembly services.

PCB circuit board heat treatment

writer: G January 15, 2019

1. High heat generating device with heat sink and heat conducting plate

When there are a few devices in the PCB that generate a large amount of heat (less than 3), a heat sink or a heat pipe can be added to the heat generating device. When the temperature cannot be lowered, a heat sink with a fan can be used to enhance heat dissipation. effect. When the amount of heat generating devices is large (more than 3), a large heat sink (board) can be used, which is a dedicated heat sink customized according to the position and height of the heat generating device on the PCB board or a large flat plate radiator. The upper and lower parts of the different components are placed. The heat shield is integrally fastened to the component surface, and is in contact with each component to dissipate heat. However, due to the poor consistency of the components during welding, the heat dissipation effect is not good. A soft thermal phase change thermal pad is usually added to the component surface to improve heat dissipation.

2. Cooling through the PCB board itself

Currently widely used PCB sheets are copper-clad/epoxy glass cloth substrates or phenolic resin glass cloth substrates, and a small amount of paper-based copper-clad sheets are used. Although these substrates have excellent electrical properties and processing properties, they have poor heat dissipation properties. As a heat dissipation path for high-heat-generating components, it is hardly expected to conduct heat from the resin of the PCB itself, but to dissipate heat from the surface of the component to the surrounding air. However, as electronic products have entered the era of miniaturization, high-density mounting, and high-heating assembly, it is not enough to dissipate heat from the surface of a component with a very small surface area. At the same time, due to the large number of surface mount components such as QFP and BGA, the heat generated by the components is transferred to the PCB in a large amount. Therefore, the best way to solve the heat dissipation is to improve the heat dissipation capability of the PCB itself in direct contact with the heat generating components. Conducted out or emitted.

3. Use reasonable wiring design to achieve heat dissipation

Since the resin in the sheet has poor thermal conductivity, and the copper foil line and the hole are good conductors of heat, increasing the copper foil residual ratio and increasing the heat conducting hole are the main means of heat dissipation.

To evaluate the heat dissipation capability of the PCB, it is necessary to calculate the equivalent thermal conductivity (nine eq) of the composite material composed of various materials having different thermal conductivity.

4. For devices that use free convection air cooling.

It is preferable to arrange the integrated circuits (or other devices) in a vertically long manner or in a horizontally long manner.

5. The devices on the same printed board should be arranged as far as possible according to their heat generation and heat dissipation. 

Devices with low heat generation or poor heat resistance (such as small signal transistors, small scale integrated circuits, electrolytic capacitors, etc.) should be placed. At the uppermost flow (inlet) of the cooling airflow, devices with large heat or good heat resistance (such as power transistors, large scale integrated circuits, etc.) are placed at the most downstream of the cooling airflow.

6. In the horizontal direction, the high-power devices are placed as close as possible to the edges of the printed board to shorten the heat transfer path.

In the vertical direction, the high-power devices are placed as close as possible to the top of the printed board to reduce the operation of these devices to other devices. The effect of temperature.

7. Temperature sensitive devices should be placed in the lowest temperature area (such as the bottom of the device).

Do not place it directly above the heating device, and multiple devices are preferably staggered in a horizontal plane.

8. The heat dissipation of the printed circuit board in the equipment mainly depends on the air flow.

So the air flow path should be studied during the design, and the device or printed circuit board should be properly configured. When the air flows, it tends to flow in a place with low resistance. Therefore, when configuring the device on the printed circuit board, avoid leaving a large air space in a certain area. The same problem should be noted in the configuration of multiple printed circuit boards in the whole machine.

9. Avoid the concentration of hot spots on the PCB.

Distribute the power evenly on the PCB as much as possible, and keep the temperature performance of the PCB surface uniform and consistent. It is often difficult to achieve a strict uniform distribution during the design process, but it is necessary to avoid areas where the power density is too high, so as to avoid the hot spots affecting the normal operation of the entire circuit. If necessary, it is necessary to perform thermal performance analysis of printed circuits. For example, the thermal performance index analysis software modules added in some professional PCB design software can help designers optimize circuit design.

10. Place the device with the highest power consumption and maximum heat generation near the best position for heat dissipation. 

Do not place higher heat generating components on the corners and peripheral edges of the printed board unless a heat sink is placed near it. When designing the power resistor, choose a larger device as much as possible, and have enough space for heat dissipation when adjusting the layout of the printed board.

11. High heat dissipation devices should minimize the thermal resistance between them when they are connected to the substrate. 

In order to better meet the thermal characteristics requirements, some thermal conductive materials (such as a layer of thermal silica gel) can be used on the bottom surface of the chip, and a certain contact area is maintained for the device to dissipate heat.

12. Connection of device to substrate:

(1) Minimize the length of the device leads;

(2) When selecting a high-power device, the thermal conductivity of the lead material should be considered, and if possible, try to select the maximum cross-section of the lead;

(3) Select a device with a large number of pins.

13. Device package selection:

(1) When considering thermal design, pay attention to the package description of the device and its thermal conductivity;

(2) Consideration should be given to providing a good thermal conduction path between the substrate and the device package;

(3) Air partitions should be avoided on the heat conduction path. If this is the case, a thermal conductive material can be used for filling.


  • PCB
  • SMT
  • Stencil

Dimensions:(mm)

×

Quantity:

Layers:

Thickness:

Quote now